How to Troubleshoot Ham Radio Operational Problems


By H. Ward Silver

Operational problems with ham radios fall into three categories: power, data, and control. After you determine which type of problem you have, you often come very close to identifying the cause of the problem.

Data problems

Data problems are more and more common in modern radio shacks. Interfaces among computers, radios, and data controllers usually are made with RS-232 or USB connections. Internet-connected equipment uses Ethernet or Wi-Fi networks. If you installed new equipment and can’t get it to play with your other equipment, four common culprits are to blame:

  • Baud rate: An improper baud rate (or the data framing parameters of start bits, stop bits, and parity of the RS-232 link) renders links inoperative, even if the wiring is correct. Baud rate specifies how fast data is sent. The framing parameters specify the format for each byte of data. These parameters are usually set by a menu or software configuration.
  • Protocol errors: Protocol errors generally result from a mismatch in equipment type or version. A program using a Kenwood radio-control protocol can’t control a Yaesu or Ten-Tec radio, for example. Be sure that all the equipment involved can use the same protocol or is specified for use with the exact models you have.
  • Improper wiring configuration: Be sure that you used the right cables. A null modem RS-232 cable or a crossover network cable may be required.
  • Network problems: These problems are in a class of their own, but the equipment generally has a configuration or setup procedure that you can perform or review to see whether you have these problems.

If equipment that was communicating properly suddenly fails, you may have a loose cable, or the configuration of the software on one end of the link may have changed. Double-check the communications settings, and inspect the connections carefully.

USB interfaces go through a process of establishing a connection when the cable is connected. On a computer, icons indicate that the equipment is recognized and working properly (or not). On stand-alone equipment, you may see indicator lights change or icons on a display. Check the user manual, and watch for these changes carefully.

Control problems


Control problems are caused by either the infamous pilot error (in other words, you) or actual control input errors.

Pilot error is the easiest, but most embarrassing, type to fix. Follow these steps to fix your error:

  • Check that all the operating controls are set properly. Bumping or moving a control by accident is easy. Refer to the operator’s manual for a list of settings for the various modes. Try doing a control-by-control setup, and don’t forget the controls on the back panel or under an access panel.Speaking from hard personal experience, before you decide that a radio needs to go to the shop, check every control on the front panel, especially squelch (which can mute the audio), MOX (which turns the transmitter on all the time), and Receive Antenna (which makes the receiver sound dead if no receive antenna is attached).If you’re really desperate, most radios have the capability to perform a hard reset, which restores all factory default settings but also wipes out the memory settings.
  • Disconnect every cable from the radio one at a time, except for power and the antenna.Start with the cable that contains signals related to the problem. If the behavior changes for any of the cables, dig into the manual to find out what that cable does. Could any of the signals in that cable cause the problem? Check the cable with an ohmmeter, especially for intermittent shorts or connections, by wiggling the connector while watching the meter or listening to the receiver.about:blank
  • If the equipment isn’t responding to a control input, such as keying or PTT, you need to simulate the control signal.Most control signals are switch or contact closures between a connector pin and ground or 12V. You can easily simulate a switch closure with . . . a switch! Replace the control cable with a spare connector, and use a clip lead (a wire with small alligator clips on each end) to jumper the pin to the proper voltage.You may want to solder a small switch to the connector with short wires if the pins are close together. Make the connection manually, and see whether the equipment responds properly. If so, something is wrong in the cable or device generating the signal. If not, the problem is in the equipment you’re testing.

At this point, you’ll probably have isolated the problem to a specific piece of equipment, and your electronics skills can take over. You have a decision to make. If you’re experienced in electronics and have the necessary information about the equipment (schematic or service manual), by all means go ahead with your repairs. Otherwise, proceed with caution.


Categories: Technology

Tagged as: ,

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s